This guest blog post was written by Keith Riley, Ehren Kiker, and Duane Muir, of Endress+Hauser.
Pressure transmitters used in the process industries are very durable and reliable instruments. Even so, they still require periodic maintenance and calibration to ensure optimal performance. This is an area of confusion for many. Typical questions include:
As with most things in life, there is no “one size fits all” answer. However, there are simple best-practice guidelines, which can be modified to fit specific applications. This article helps answer the basic questions facing process plant personnel with regard to calibration.
Each process plant has to determine correct calibration intervals based upon historical performance and process-related requirements. Factors you need to consider that may influence this decision are:
If you have no significant history or regulatory requirements to guide you in developing your calibration procedures, a good place to start is with the following general guidelines.
If a remote diaphragm seal is employed on a pressure transmitter, the calibration interval should be reduced by a factor of two (i.e., a four-to-six year interval is reduced to two to three years). This is because a remote diaphragm seal employs more fill fluid than a direct-mounted configuration. Consequently, it will experience more mechanical stress from process or ambient temperature fluctuations. Most remote diaphragms are flush faced where the diaphragm/membrane is susceptible to physical damage (dents or abrasions) that can cause offset or linearity issues. If the process regularly experiences significant pressure swings or overpressurization events, reducing the calibration interval by a factor of two is a good rule of thumb.
How good is good enough? In other words, what is the maximum permissible error (MPE) for your calibration? Many make the mistake of adopting the manufacturer’s reference accuracy as their calibration target. Unfortunately, this means they will have an MPE that is too tight, with a high rate of nonconformance in their calibration process. In the worst case, with a very tight tolerance MPE, it may not be possible for their field or lab test equipment to calibrate some of their transmitters.
A manufacturer’s reference accuracy is based upon tightly controlled environmental conditions that are seldom, if ever, duplicated in a plant environment. Using that reference accuracy for a calibration target also fails to take into account the long-term stability of the instrument.
Over time, all instruments experience slight accuracy degradation due to aging and simple wear and tear on mechanical components. This needs to be considered when establishing the MPE. In general, unless there are mitigating circumstances, it is better to set a reasonable MPE that is achievable with standard field and lab test equipment.
Test equipment starts with an accurate pressure source to simulate the transmitter input. The corresponding output is measured with a multimeter for a 4–20 mA transmitter, or with a specialized device for smart transmitters with digital outputs, such as HART, FOUNDATION Fieldbus, Profibus, or EtherNet/IP.
The test equipment you intend to use should be traceable to the National Institute of Standards and Technology. As a general recommendation, your reference equipment should be at least three times more accurate than the pressure transmitter being calibrated.
Once you have established the calibration interval and MPE, you are ready to perform the actual calibration procedure on your pressure transmitter. The best-practice recommendation is:
The calibration should be performed in as stable an environment as possible, because temperature and humidity can influence the pressure transmitter being tested as well as the pressure reference. If the results of your calibration are within the MPE, do not attempt to improve the performance of the transmitter.
One mistake many end users make is to regularly perform a sensor trim adjustment of their pressure transmitter—even on new units. A sensor trim corrects the digital reading from the sensor after the analog/digital conversion. Performing a sensor trim on a new transmitter is essentially a single-point calibration under the current plant environment conditions, as opposed to sticking with the original factory calibration.
Factory calibrations of pressure transmitters are performed in a tightly controlled environment and incorporate as many as 100 test points. Performing a sensor trim on a new pressure transmitter under field conditions will cause the unit to operate at less than optimal capacity. A sensor trim should only be performed by a qualified technician under the manufacturer’s guidance.
Even with the sophisticated calibration and reference equipment currently available, there is no substitute for a properly trained technician when it comes to calibrating pressure transmitters. Not only does the technician need to be trained on the mechanics of the calibration process, he or she also must be equally qualified in completing and maintaining the documentation. Repeatability is the key. In the world of calibration, if it is not properly documented, it did not happen.
Occasionally there are calibrations that cannot be performed in a standard maintenance shop by maintenance technicians. For these cases, an ISO 17025–accredited organization is required. Not only can an ISO 17025–accredited organization perform more stringent calibrations, it provides other value as well:
The “correct” calibration cycle for a pressure transmitter depends on the purpose of the calibration and the application. The same pressure transmitters employed in different operating units or processes at the same plant may require different calibration intervals.
Even more important than the calibration interval of the instrument are:
Following these guidelines and using judgment based on actual plant operational conditions will help establish proper calibration practices, saving money while maintaining acceptable performance.
Blog Posts
How Often Do Measurements Need to Be Calibrated?
Just in Time, or Just Too Late? A Kaizen Approach to Calibration
How to Improve Industrial Productivity with Loop Calibration
Temperature Calibration: Using a Dry Block to Calculate Total Uncertainty
How Can Advanced Calibration Strategies Improve Control Performance?
How to Calibrate a Pressure Transmitter
Webinar Recordings
Uncertainty in Calibration
Calibration Uncertainty and Why Technicians Need to Understand It
How to Avoid the Most Common Mistakes in Field Calibration
Learn Advanced Techniques in Field Calibration
How to Build an Industrial Calibration System Business Case
How to Use Calibration Tools for Accurate Process Temperature Measurement
How Does Low Flow Affect Differential Pressure Flowmeter Calibration?
Three Common Pitfalls of Pressure Calibration
How to Calibrate Differential Pressure Flowmeters
Free Downloads
ISA Industrial Calibration Worksheets
Measurement Uncertainty Analysis Excel template plus book excerpt
Calibration Handbook of Measuring Instruments book excerpt
In-Depth Guide to Calibration for the Process Industries eBook
Calibration Uncertainty for Non-Mathematicians white paper
About the Author
Keith Riley joined Endress+Hauser in 2008 as a level product manager. He was responsible for the business development and technical direction of level products. After four years, he became the national product team leader for pressure and temperature products. In this role, Riley markets the temperature and pressure products and oversees the strategic direction for the U.S. temperature and pressure product business team.
About the Author
Ehren Kiker has spent the past 20 years consulting on process instrumentation and control as well as electrical control and distribution equipment. He received his bachelor’s degree in industrial and systems engineering from the University of Florida and his MBA from the University of Houston. Kiker is the national product marketing manager for Endress+Hauser U.S. He is responsible for technology application, marketing, and business development for a wide range of pressure and temperature products.
About the Author
Duane Muir is currently a technical product specialist for level and pressure products at Endress+Hauser with 20 years of experience in application, installation, calibration, and troubleshooting instrumentation. He received his BS at Indiana State University in electronics technology. In his career, Muir has specialized in five different areas of instrumentation technology and has multiple certifications from Endress+Hauser.
A version of this article also was published at InTech magazine.