This guest blog post is part of a series written by Edward J. Farmer, PE, ISA Fellow and author of the new ISA book Detecting Leaks in Pipelines. To read all the posts in this series, scroll to the bottom of this post for the link archive.
Suppose we want to do leak detection on a segment of a pipeline transporting a petroleum fluid from one place to another. Perhaps this segment directly connects the ends, maybe a pump or compressor station at the high-pressure end to a storage facility or another pipeline at the low-pressure end. We may know the length, L, the diameter of flow, D, perhaps some pipe wall properties such as the wall roughness, the elevation of each end relative to a common datum, and some things about the fluid.
To define this as a hydraulic segment we draw a dotted line, a “box,” around it, generally with consideration of where the various instruments we use to observe its operation are located. Let’s assume we have observations (measurements) of pressure and flow at each end; four observations in all. Further, we know that the pressure inside the pipe is significantly higher that the pressure of the environment around it. In normal operation we would expect that:
If a leak occurs on the segment, we would expect the following things to happen:
A detection algorithm could be based on the idea that the coherent occurrence of all four of those conditions is “sufficient” to detect a leak. Each of those conditions is independently “necessary,” but all four are necessary for “sufficiency.” Considering that criteria for leak detection we need observability of those four measurements in a time scheme that ensures we can establish they are all the result of the same disturbance (the leak event).
Over time, the leakage rate usually stabilizes, and the leaking pipeline migrates its operation to a new steady state in which all four conditions are evident. If the leak is stable so will be this new operating condition. Those are the observations with which we can do our analysis.
The enormous assumption thus far in this discussion is that the fluid is everywhere the same – homogeneous throughout the segment and at its ends. What if the pressure drop at the leak location is sufficient to flash some of the normally liquid flow into gas? That might limit flow through the leak path and it might change the nature of flow inside the pipe near the leak location from liquid to multiphase.
We may also discover that a leak hole of a particular size might support a much smaller mass flow rate than might be expected if conditions in the leak were the same as in the pipeline. The fastest the fluid can leak is sonic velocity and the density of the fluid at low pressure will be much smaller than at pipeline conditions. There will be a blog about such issues in the future.
Note that the term “coherence” snuck in here. It’s there to foreshadow an upcoming blog about discerning whether of not a series of observed events are, in fact, related – spawned from the same event.
At present, though, the discussion is on necessary and sufficient conditions and the significance we might attach to them.
Suppose all of the conditions are met except the upstream flow decreases instead of increasing? Depending on the upstream process equipment (e.g., a pump) it might be possible the flow would remain constant as opposed to increasing but there is usually no way a leak would cause it to decrease. A bit more thought might reveal the detected condition is, while similar to what could be expected from a leak, exactly what would occur with a shutdown or a decrease to a lower flow rate. The presence of the other three conditions are a necessary outcome of a leak, but without the appropriate behavior of upstream flow they are not sufficient.
Often, there is some seldom-used feature or unusual operating condition that can mimic most of what is necessary for a set of events to be detected as a leak. Such things can result in false alarms. Possibly the most capable engineer I’ve ever worked with was once challenged with determining why a largely above-ground pipeline in Alaska would produce false alarms with no discernable reason whatsoever.
To service one of these “probably false” alarms he was driving across an uncharacteristically bright and sunny North Slope and found himself thinking, “Well, at least these things always happen on nice and sunny days!” With that thought he changed his thinking to sun-sensitive issues and discovered a subtle problem stemming from some unproductive assumptions about a key pipeline measurement. The irritating and recurring problem was over by the end of the day.
Understanding how the process system and automation equipment work is crucial: sometimes there is a problem to fix, sometimes some process condition is screaming for attention, sometimes there is an unproductive or incorrect assumption about how things actually work. All that is fixable. Sometimes there is just one more process condition or issue that you need to know. When that is the case you need to make a way to observe it.
Book Excerpt + Author Q&A: Detecting Leaks in Pipelines
How to Optimize Pipeline Leak Detection: Focus on Design, Equipment and Insightful Operating Practices
What You Can Learn About Pipeline Leaks From Government Statistics
Is Theft the New Frontier for Process Control Equipment?
What Is the Impact of Theft, Accidents, and Natural Losses From Pipelines?
Can Risk Analysis Really Be Reduced to a Simple Procedure?
Do Government Pipeline Regulations Improve Safety?
What Are the Performance Measures for Pipeline Leak Detection?
What Observations Improve Specificity in Pipeline Leak Detection?
Three Decades of Life with Pipeline Leak Detection
How to Test and Validate a Pipeline Leak Detection System
Does Instrument Placement Matter in Dynamic Process Control?
Condition-Dependent Conundrum: How to Obtain Accurate Measurement in the Process Industries
Are Pipeline Leaks Deterministic or Stochastic?
How Differing Conditions Impact the Validity of Industrial Pipeline Monitoring and Leak Detection Assumptions
How Does Heat Transfer Affect Operation of Your Natural Gas or Crude Oil Pipeline?
Why You Must Factor Maintenance Into the Cost of Any Industrial System
Raw Beginnings: The Evolution of Offshore Oil Industry Pipeline Safety
How Long Does It Take to Detect a Leak on an Oil or Gas Pipeline?
About the Author
Edward Farmer has more than 40 years of experience in the “high tech” part of the oil industry. He originally graduated with a bachelor of science degree in electrical engineering from California State University, Chico, where he also completed the master’s program in physical science. Over the years, Edward has designed SCADA hardware and software, practiced and written extensively about process control technology, and has worked extensively in pipeline leak detection. He is the inventor of the Pressure Point Analysis® leak detection system as well as the Locator® high-accuracy, low-bandwidth leak location system. He is a Registered Professional Engineer in five states and has worked on a broad scope of projects worldwide. His work has produced three books, numerous articles, and four patents. Edward has also worked extensively in military communications where he has authored many papers for military publications and participated in the development and evaluation of two radio antennas currently in U.S. inventory. He is a graduate of the U.S. Marine Corps Command and Staff College. He is the owner and president of EFA Technologies, Inc., manufacturer of the LeakNet family of pipeline leak detection products.